Varorna som visas här är relaterade till varandra med varan du valt och beställs eller söks ofta tillsammans.
Tips: får du ingen bra träff på sökordet du angivit så försök då att söka en vara som är relaterad till den. Finns det då en flik relaterade varor så kanske du hittar varan du sökte där.
Återuppbyggd motor 1775cc (nytt hölje) och kärndeponering
Type 1 engine 1775cc
Återuppbyggnad av motor 1600cc (AD/AJ/AS) (nytt hölje) och deponering av kärnor
Type 1 engine 1600cc (enginecode AD, AJ or AS) dual port with 200 mm flywheel
Note:
Price includes €370,- core deposit.
Produktnummer : 5503 Original VW nummer : 211100033
SEK 60609,00
Motorn byggs i uppdrag till dig, detta innebär en leveranstid på minst 10 veckor.
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
replacing the sump plate studs If the studs are not tightened properly, it is practically impossible to tighten the crankcase sump plate to compress the paper gaskets. The infamous engine oil leak is the result, and no, it is not normal for an air-cooled VW to leak! A leaking engine will be rejected at the mandatory technical inspection.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
Engine overhaul - video 11 the clutch To disassemble the flywheel, you will need to loosen the gland nut, we discuss that in video 12. But first you will need to disassemble the clutch. You can do that when the engine is on the workbench, or hanging from an engine mount. In this video we show various techniques and tools to disassemble the clutch of your Type 1 Volkswagen engine without damage.
crankshaft seal replacement If you find that the crankshaft clearance is outside the factory specifications, replacing the crankshaft seal will not be a solution for the oil leak you have identified. If the crankshaft clearance is less than 0.30 mm, it makes sense to replace the oil seal, otherwise a total engine overhaul is the only worthwhile option.
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
oil consumption Oil leaks are easy to rectify, sometimes even without having to remove the motor. We have saved the more difficult cases for this article, so we did not call this "oil leaks part 2" but "oil consumption". The distinction between the two is sometimes difficult to make, hopefully the information that follows will bring clarity.
cylinder head specifications One of the most heavily loaded parts in the air-cooled VW engine is undoubtedly the cylinder head. Especially the valves, valve guides and valve seats have to endure a lot because of the high temperatures, the temperature differences and the mechanical load in an air-cooled engine.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?