Varorna som visas här är relaterade till varandra med varan du valt och beställs eller söks ofta tillsammans.
Tips: får du ingen bra träff på sökordet du angivit så försök då att söka en vara som är relaterad till den. Finns det då en flik relaterade varor så kanske du hittar varan du sökte där.
Återuppbyggd motor 1775cc (nytt hölje) och kärndeponering
Type 1 engine 1775cc
Återuppbyggnad av motor 1600cc (AD/AJ/AS) (nytt hölje) och deponering av kärnor
Type 1 engine 1600cc (enginecode AD, AJ or AS) dual port with 200 mm flywheel
Note:
Price includes €370,- core deposit.
Produktnummer : 5503 Original VW nummer : 211100033
SEK 62578,00
Motorn byggs i uppdrag till dig, detta innebär en leveranstid på minst 10 veckor.
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
crankshaft end play Whether an oil leak is caused by a defective crankshaft seal or O-ring/packaging is not always easy to determine. At the bottom of the engine, near the flywheel, where the gearbox and the engine are connected to each other, you will see traces of engine oil.
replacing the sump plate studs If the studs are not tightened properly, it is practically impossible to tighten the crankcase sump plate to compress the paper gaskets. The infamous engine oil leak is the result, and no, it is not normal for an air-cooled VW to leak! A leaking engine will be rejected at the mandatory technical inspection.
engine types and codes The engine number indicates which type of engine is involved and with which engine capacity. The first letter(s) determine the capacity and type of engine and the following figures determine the year of manufacture. The engines up to and including July 31, 1965 had no letters for the engine number, which is why up to and including this year of manufacture only numbers are given.
sump plate stud length How many VW enthusiasts are surprised that the engine leaks after an oil change? Read all about the type 1 sump plate in edition 20, what to look out for, how to attach it and with which tools. In this edition we will determine the maximum length of the sump plate studs, to prevent oil leaks.
Engine diagnostics - video 03 pushrods In video fourteen of our series on engine overhaul, we disassembled and reassembled the rocker arms and pushrods. In this video, we will inspect the pushrods. The result of this diagnosis, will tell us if we can reinsert the pushrods, or if we need to replace them.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
cylinder head specifications One of the most heavily loaded parts in the air-cooled VW engine is undoubtedly the cylinder head. Especially the valves, valve guides and valve seats have to endure a lot because of the high temperatures, the temperature differences and the mechanical load in an air-cooled engine.