Do you have the product from the page mounted on your car? Take a clear picture or video of it and put it in the spotlights. This way your car gets admired by a lot of people and others can see what the product looks like. We reward your effort with a € 1,- discount code for every approved photo or video. Use the discount on your next order. Click here to upload your photo Click here to upload your video
Fits: Type-1 engines and replaces the Solex:
34 PICT-3
34 PICT-4
Defect(s):
-The CO cannot be properly adjusted
What is a second chance part? A second chance part is a part that has been returned by a customer and can no longer be sold as new or it has suffered damage during transport. Damage or incompleteness are the most common defects. The defect is described above and the image is the true representation of the relevant part. Click on the original Paruzzi number for more information about the part and images of the original part.
Second chance parts can not be returned and do not have any form of warranty, but you will benefit from a pleasant discount on the new price.
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 16 part 2 valves removal In Part 1, we showed the basic techniques for disassembling the valves and valve springs. We did this on a fairly new cylinder head.
When you`re dealing with a used cylinder head, disassembly may be a little less smooth.
Engine overhaul - video 13 replacing the crank seal During a complete engine overhaul, you will need to replace the crank seal. But replacement may also be necessary, when you discover an oil leak behind the flywheel, which will impair the operation of the clutch. We show in this video how to disassemble and reassemble the crank seal.
Engine Overhaul - video 01 video series preview In this video, we will give an overview of the most important steps during the engine overhaul of a type 1 air-cooled Volkswagen engine. Each step will be discussed in a separate video. We will show special tools and even homemade tools to help the enthusiast perform their engine overhaul.
adjust type 1 carburetor The adjustment of the carburetor will determine the behavior of the engine. There are two types of carburetors for the type 1 engine when it comes to adjustment. The old generation (up to SOLEX 30 PICT-2) with two adjusting screws and the young generation with three adjusting screws (from SOLEX 30 PICT-3), recognizable by the large screw in the carburetor housing.
fuel circuit - concept The combustion engine of our air-cooled Volkswagen uses a mixture of petrol and air. It is extremely important that both the amount of air and the purity of the air are regulated, this also applies to the petrol. Unfortunately, the petrol circuit is not very well known to enthusiasts and it is not always well maintained.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
air filter thermostat The preheating of the fresh air supplied via the air filter to the carburettor is a part of our VW engine that gets too little attention. This system will ensure that in all weather conditions the carburettor is supplied with air at the right temperature. With these younger air filter models you don't have to adjust anything in contrast to the older models.
Engine diagnostics - video 02 rockers and rocker arm In video fourteen of our engine overhaul video series, we disassembled and reassembled the rocker arms and rocker shaft. We will diagnose the rocker arms and rocker shaft in this video. Additional attention will be paid to the adjusting screws and adjusting nuts.
Engine overhaul - video 12 the flywheel In this video, we'll explain how to disassemble and assemble the flywheel, and what tools you'll need to do so. To disassemble the flywheel, you will need to unscrew the gland nut. This nut is attached with a torque of 350 Nm, it will require some force to loosen.
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.