M8 hex muttrar ga 10 st
Gängstorlek: M8 x 1.25
Höjd: 6.26 mm
Material: galvanized steel
Wrench size: 13 mm Produktnummer : 7417 Original VW nummer : N01100830, N01100818, N110088, N0110088, N110083, N110085
Varorna som visas här är relaterade till varandra med varan du valt och beställs eller söks ofta tillsammans.
Tips: får du ingen bra träff på sökordet du angivit så försök då att söka en vara som är relaterad till den. Finns det då en flik relaterade varor så kanske du hittar varan du sökte där.
Justerskruvar M8 (8 stycken) för ventiler med hög utväxling
Type 1 till och med 1983 (VIN 11-E-119 815)
Type 3
Type 4 1700cc
CT/CZ Produktnummer : 3784
Vipparm 1.25: 1 8st
Type 1 8.1960 och senare
Karmann Ghia 8.1960 och senare
Bus 12/13/15/1600cc 8.1960 och senare
T25/T3 buss Waterboxer engines
Type 3
Type 181 Produktnummer : 1783
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
Engine diagnostics - video 04 part 1 valves and valve springs In video 16 of the engine overhaul series, we disassembled the valves and valve springs.
Not all of the cylinder heads we showed were in good condition, this does not mean that all parts need to be replaced. After a thorough diagnosis, it will show if the valves and valve springs are still reusable. This video discusses valve and valve spring diagnosis. It consists of four parts.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?
setting valve clearance The first technical work I ever did on my first Volkswagen Beetle was to set the valves. I didn't know much about the technology of the VW Beetle at the time, but I dared to do it, valve setting is easy to do yourself, you don't need many tools, and it's essential for the proper functioning of your classic.
Engine overhaul - video 15 disassemble cylinder heads In this video, we will show how to disassemble the cylinder heads of a VW Type 1 engine, and what challenges you may face.
Engine overhaul - video 20 pushrod tubes With the cylinder heads out of the way, you can install standard pushrod tubes. But, disassembling the cylinder heads means replacing the gasket between cylinders and crankcase.
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
Engine overhaul - video 11 the clutch To disassemble the flywheel, you will need to loosen the gland nut, we discuss that in video 12. But first you will need to disassemble the clutch. You can do that when the engine is on the workbench, or hanging from an engine mount. In this video we show various techniques and tools to disassemble the clutch of your Type 1 Volkswagen engine without damage.