Do you have the product from the page mounted on your car? Take a clear picture or video of it and put it in the spotlights. This way your car gets admired by a lot of people and others can see what the product looks like. We reward your effort with a € 1,- discount code for every approved photo or video. Use the discount on your next order. Click here to upload your photo Click here to upload your video
Sale
Fits: Type-1 engines 8.1969 and later
Type-3 engines 8.1969 and later
Paruzzi number:
03993
€ 99,92 excluding VAT € 120.9 including VAT
in stock: 2 Order before 14:00 CET on Monday through Friday and we ship the same day. Will be sent via UPS
The parts mentioned here have a close relationship with the selected part and are often ordered along with the selected part or searched for.
Tip: if you do not get a good search result when entering a keyword try a part that has something to do with it, if there is a related tab, the searched item is often mentioned there.
Aluminum full flow oilpump cover with pressure valve
Type-1 engines:
1200cc 1967 (D 0230001) and later
1300cc 1967 (E 0013651 and F 1225018) until 7.1970 and 8.1970 and later (all 1300cc engines codes)
1500cc 1967 (L 0018100 and H 0822052) and later
1600cc Paruzzi number : 3992
Useful information from Paruzzi magazine and from our YouTube channel :
Engine diagnostics - video 04 part 2 valves and valve springs In the second and third parts of this video, we will measure valve spring pressure. We begin in part 2 by measuring the valve spring pressure at open valve. Also known as the valve spring pressure at maximum valve lift. In part 3, we will measure the valve spring pressure at installed length.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
type 1 sump plate Replacing the crankcase oil of a Type 1 engine is a job every VW enthusiast has done once in a while. It involves loosening a few nuts, replacing gaskets and tightening everything again, right?
It seems a simple operation, but nothing could be further from the truth.
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine diagnostics - video 03 pushrods In video fourteen of our series on engine overhaul, we disassembled and reassembled the rocker arms and pushrods. In this video, we will inspect the pushrods. The result of this diagnosis, will tell us if we can reinsert the pushrods, or if we need to replace them.
oil pressure gauge After an engine rebuild, when you start the engine for the first time, and when you start driving, you need to keep a close eye on a number of engine parameters. The most important are oil pressure, engine oil temperature and cylinder head temperature.