Do you have the product from the page mounted on your car? Take a clear picture or video of it and put it in the spotlights. This way your car gets admired by a lot of people and others can see what the product looks like. We reward your effort with a € 1,- discount code for every approved photo or video. Use the discount on your next order. Click here to upload your photo Click here to upload your video
Fits: Type-1 dual port engines
Type-3 dual port engines
CT/CZ engines
Specifications:
Cylinder head Ø: 101 mm
Bore: 94 mm
Combustion chamber: 58cc
Valves: 40 x 35.5 mm stainless steel
Valve springs: dual
Paruzzi number:
01874
€ 464,59 excluding VAT € 562.15 including VAT
in stock: 1 Order before 14:00 CET on Monday through Friday and we ship the same day. Will be sent via UPS
Silicone pushrod tube seals (16 pieces)
Type-1 engines except 25hp+30hp
Type-3 engines
CT/CZ engines for the cylinder head side
Waterboxer engines for the cylinder head side Paruzzi number : 1751
These parts can offer an alternative to the selected part, for example a different quality, color, variation, etc.
EMPI GTV-2 big bore cylinder head (each)
Type-1 dual port engines
Type-3 dual port engines
CT/CZ engines
Specifications:
Cylinder head Ø: 98 mm
Bore: 88, 90.5 or 92 mm
Combustion chamber: 58cc
Valves: 40 x 35.5 mm Stainless Steel
Valve springs: dual Paruzzi number : 1736
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
replace a thread When you are working on your VW, you will encounter this problem at some point; a bolt of the crankcase cover doesn't really turn in the thread in the crankcase anymore. The more you try, the worse it gets. There is too little tension between the crankcase cover and crankcase, with oil leakage as a result.
Engine Overhaul - video 02 overhauled engines We show in this video all the engines that we overhauled for the video series. An AB 1300, an AS 1600, an AJ 1600 and a D 1200 engine, every step, every detail of the overhaul of these air-cooled Volkswagen engines will be discussed in this series.
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
Type 1 engine mount In this article we show how to mount the engine of a VW Beetle or Karmann Ghia, so it becomes clear what to look out for when you mount the engine and build it back in.
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
installing the engine In edition 16 we explained how to remove the engine of a VW Beetle, two techniques were discussed. The most important points of attention for the installation of the engine are indicated in this article. During the installation of the engine you will have to position the pilot shaft of the gearbox perfectly opposite the centre of the clutch.
measure crankshaft end play The play is caused by wear of the engine, this is actually very normal, and will occur faster with performance engines. With normal use of standard VW engines in combination with a good maintenance of the engine, wear will not occur quickly.
Engine overhaul - video 12 the flywheel In this video, we'll explain how to disassemble and assemble the flywheel, and what tools you'll need to do so. To disassemble the flywheel, you will need to unscrew the gland nut. This nut is attached with a torque of 350 Nm, it will require some force to loosen.