Oppmerksomhet: Alle norske bestillinger vil bli sendt av Winston VW Veteran AS (Sandnes, Norge),
så fraktkostnader er nå mye lavere og alle lokale avgifter er nå inkludert i prisen. På store karosserideler må det beregnes leveringstid, og høyere Innenlandsfrakt.
Disse delene bestilles vanligvis sammen med den valgte delen. De er ikke inkludert i leveransen, men byttes ofte ut sammen.
Pakninger til oljepumpe (sett)
Type 1:
1200cc 1967 (D 0230001) og senere
1300cc 1967 (E 0013651 and F 1225018) og senere
1500cc 1967 (L 0018100 and H 0822052) og senere
1600cc
Type 3:
1500cc 1967 (K 0090196) og senere
1600cc 1967 (T 0445098) og senere
CT/CZ
Type 4 (only one gasket can be used)
Waterboxer Motorer Artikkelnummer : 1998 Original VW nummer : 111115131B, 111115111B
Disse delene leveres eller følger med den delen du har valgt nå, og du kan bruke disse delene til å reparere den valgte delen.
Original oljefilter
stock replacement:
Type 1 Motorer 10.1992 og senere
other applications:
replacement for oilpump #1806 and #1807
to be used for adapter #1825 and #3827 Artikkelnummer : 1826 Original VW nummer : 056115561G
Delene som er nevnt her, har en nær sammenheng med den valgte delen og blir ofte bestilt sammen med den valgte delen eller søkt etter.
Tips: Hvis du ikke får et godt søkeresultat når du skriver inn et søkeord, prøv en del som har noe med det å gjøre, hvis det er en relatert fane, er den søkte delen ofte nevnt der.
Hvis den valgte delen ikke gjelder for din Volkswagen-type, kan du sjekke denne listen over de samme delene som passer på andre byggeår eller andre biltyper.
Full flow oljepumpe med filter
Type 1 Motorer:
1300, 1500 and 1600cc 8.1969 til 7.1971
1200cc 8.1969 og senere
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
type 1 sump plate Replacing the crankcase oil of a Type 1 engine is a job every VW enthusiast has done once in a while. It involves loosening a few nuts, replacing gaskets and tightening everything again, right?
It seems a simple operation, but nothing could be further from the truth.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
Engine diagnostics - video 03 pushrods In video fourteen of our series on engine overhaul, we disassembled and reassembled the rocker arms and pushrods. In this video, we will inspect the pushrods. The result of this diagnosis, will tell us if we can reinsert the pushrods, or if we need to replace them.
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
Engine overhaul - video 13 replacing the crank seal During a complete engine overhaul, you will need to replace the crank seal. But replacement may also be necessary, when you discover an oil leak behind the flywheel, which will impair the operation of the clutch. We show in this video how to disassemble and reassemble the crank seal.
oil pressure gauge After an engine rebuild, when you start the engine for the first time, and when you start driving, you need to keep a close eye on a number of engine parameters. The most important are oil pressure, engine oil temperature and cylinder head temperature.
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.