Passar till: Bubbla 1300, 1302, 1303 8.1970 och senare
Bubbla 1200 1972 (VIN 112 2670 583) och senare
Karmann Ghia 8.1970 och senare
Bus 8.1970 och senare
Type 3 8.1970 och senare
Type 181 8.1971 och senare
Varorna som visas här är relaterade till varandra med varan du valt och beställs eller söks ofta tillsammans.
Tips: får du ingen bra träff på sökordet du angivit så försök då att söka en vara som är relaterad till den. Finns det då en flik relaterade varor så kanske du hittar varan du sökte där.
Styrhylsa urtrampningslager
Bubbla 1300-1302-1303 8.1970 och senare
Bubbla 1200 1972 (112 2670 583) och senare
Karmann Ghia 8.1970 och senare
Bus 8.1970 och senare
Type 3 8.1970 och senare
Type 181 8.1971 och senare Produktnummer : 1522 Original VW nummer : 113141181A, 016141181
Ifall varan du valt inte är tillämpningsbar på denna typ Volkswagen, finns alternativ med liknande varor som passar på andra årsmodeller eller andra fordonsmodeller.
Urtrampningslager
Bubbla 1300, 1500 till och med 7.1970
Bubbla 1200 till och med 1972 (VIN 112 2670 582)
Karmann Ghia till och med 7.1970
Bus till och med 7.1970
Type 3 till och med 7.1970
Type 181 till och med 7.1971 Produktnummer : 1520 Original VW nummer : 111141165A, 111141167C
Useful information from Paruzzi magazine and from our YouTube channel :
Engine Overhaul - video 01 video series preview In this video, we will give an overview of the most important steps during the engine overhaul of a type 1 air-cooled Volkswagen engine. Each step will be discussed in a separate video. We will show special tools and even homemade tools to help the enthusiast perform their engine overhaul.
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
measure crankshaft end play The play is caused by wear of the engine, this is actually very normal, and will occur faster with performance engines. With normal use of standard VW engines in combination with a good maintenance of the engine, wear will not occur quickly.
Engine diagnostics - video 04 part 2 valves and valve springs In the second and third parts of this video, we will measure valve spring pressure. We begin in part 2 by measuring the valve spring pressure at open valve. Also known as the valve spring pressure at maximum valve lift. In part 3, we will measure the valve spring pressure at installed length.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
oil consumption Oil leaks are easy to rectify, sometimes even without having to remove the motor. We have saved the more difficult cases for this article, so we did not call this "oil leaks part 2" but "oil consumption". The distinction between the two is sometimes difficult to make, hopefully the information that follows will bring clarity.
Engine diagnostics - video 04 part 1 valves and valve springs In video 16 of the engine overhaul series, we disassembled the valves and valve springs.
Not all of the cylinder heads we showed were in good condition, this does not mean that all parts need to be replaced. After a thorough diagnosis, it will show if the valves and valve springs are still reusable. This video discusses valve and valve spring diagnosis. It consists of four parts.