Estas peças são normalmente encomendadas com a peças seleccionada. Não estão incluídos na entrega, mas são frequentemente encomendados com junto.
Tampa de enchimento de óleo de origem
Type 1 motores 8.1955 até 9.1992 (excepto injection motores with motorescode AJ) Referência Paruzzi : 3883 Referencia VW original : 111115485
Junta para tubo de enchimento de óleo ou caixa de ventilação do cárter
Type 1 motores excepto 25hp+30hp
Type 3 motores Referência Paruzzi : 3847 Referencia VW original : 113115475
As peças aqui mencionadas têm uma relação forte com a peça seleccionada e são frequentemente encomendadas juntamente com a peça seleccionada ou procuradas. Tip: Se não receber um bom resultado de busca quando entrar numa palavra-chave, tenta uma parte que tenha algo a ver com ela, se existe uma lista relatada, o item revistado é frequentemente mencionado lá
Porca, entrada de óleo
Type 1 / Karmann Ghia 8.1960 e mais tarde (not 30hp)
Furgão Pão de Forma 12/13/15/1600 8.1960 e mais tarde (not 30hp + CT)
VW 181 Referência Paruzzi : 1872 Referencia VW original : 113115495
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine overhaul - video 16 part 1 valves removal In this first part of video 16, we disassemble cylinder head valves and valve springs. In the first part, we start by demonstrating the tools and techniques used, and disassemble the valves of a relatively new cylinder head.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
oil pressure gauge After an engine rebuild, when you start the engine for the first time, and when you start driving, you need to keep a close eye on a number of engine parameters. The most important are oil pressure, engine oil temperature and cylinder head temperature.
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?
Engine diagnostics - video 02 rockers and rocker arm In video fourteen of our engine overhaul video series, we disassembled and reassembled the rocker arms and rocker shaft. We will diagnose the rocker arms and rocker shaft in this video. Additional attention will be paid to the adjusting screws and adjusting nuts.