Oppmerksomhet: Alle norske bestillinger vil bli sendt av Winston VW Veteran AS (Sandnes, Norge),
så fraktkostnader er nå mye lavere og alle lokale avgifter er nå inkludert i prisen. På store karosserideler må det beregnes leveringstid, og høyere Innenlandsfrakt.
Delene som er nevnt her, har en nær sammenheng med den valgte delen og blir ofte bestilt sammen med den valgte delen eller søkt etter.
Tips: Hvis du ikke får et godt søkeresultat når du skriver inn et søkeord, prøv en del som har noe med det å gjøre, hvis det er en relatert fane, er den søkte delen ofte nevnt der.
Justeringsskruer M8 for ventil med høyt utvekslingsforhold (8 stk.)
Type 1 til 1983 (VIN 11-E-119 815)
Type 3
Type 4 1700cc
CT/CZ Artikkelnummer : 3784
1.25 til 1 vipper (8 stk.)
Type 1 8.1960 og senere
Karmann Ghia 8.1960 og senere
Buss 12/13/15/1600cc 8.1960 og senere
T25/T3 buss Waterboxer Motorer
Type 3
Type 181 Artikkelnummer : 1783
Useful information from Paruzzi magazine and from our YouTube channel :
Engine Overhaul - video 02 overhauled engines We show in this video all the engines that we overhauled for the video series. An AB 1300, an AS 1600, an AJ 1600 and a D 1200 engine, every step, every detail of the overhaul of these air-cooled Volkswagen engines will be discussed in this series.
Engine overhaul - video 16 part 2 valves removal In Part 1, we showed the basic techniques for disassembling the valves and valve springs. We did this on a fairly new cylinder head.
When you`re dealing with a used cylinder head, disassembly may be a little less smooth.
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.
Engine overhaul - video 15 disassemble cylinder heads In this video, we will show how to disassemble the cylinder heads of a VW Type 1 engine, and what challenges you may face.
finding the top dead center What does Top Dead Center (TDC) actually mean? If you study the theory of the operation of an internal combustion engine - or the "petrol engine" - it will become clear. Without going into too much detail about the theory, we have to talk about the otto cycle, better known as the four stroke cycle.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
mesuring the compression How can you determine very objectively how much wear the engine has? An indication of the wear level can be obtained by performing a compression measurement, the engine compression determines the power of your VW. Anyone can perform a compression measurement on an air-cooled or water-cooled VW.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.