Mellomleggsplater for generator/generator (10 stk)
Oppmerksomhet: Alle norske bestillinger vil bli sendt av Winston VW Veteran AS (Sandnes, Norge),
så fraktkostnader er nå mye lavere og alle lokale avgifter er nå inkludert i prisen. På store karosserideler må det beregnes leveringstid, og høyere Innenlandsfrakt.
Delene som er nevnt her, har en nær sammenheng med den valgte delen og blir ofte bestilt sammen med den valgte delen eller søkt etter.
Tips: Hvis du ikke får et godt søkeresultat når du skriver inn et søkeord, prøv en del som har noe med det å gjøre, hvis det er en relatert fane, er den søkte delen ofte nevnt der.
Monteringssett for dynamo/vekselstrømsremskive
8.1955 og senere Artikkelnummer : 3934 Original VW nummer : 211903183, 111903181
Useful information from Paruzzi magazine and from our YouTube channel :
DC versus AC A car needs a direct voltage of 12 V or 6 V to operate, a battery can only be charged by direct current. The alternator and dynamo generate alternating current. But what is the difference between AC and DC?
replace dynamo bearings Dynamo bearings last a very long time, but they are wear parts. Wear will be promoted by an over-tightened dynamo pulley. A dynamo has two sealed ball bearings. These are bearings that do not require grease, but are factory ready to mount
radio interference Have you ever driven a classic Volkswagen with an original radio or a classic radio, then you have probably ever known the phenomenon "interference". That annoying noise, buzzing, crackling that comes out of your speakers. These disturbances can have different causes, but they can also be remedied.
6 volts and 12 volts Until the early 1970s, the VW Beetles were equipped with 6 volts in their 1200 cc version. The 1300 cc Beetle was first equipped with a 12 volt system in 1968. The VW Bus and type 3 VWs were increased to 12 volts in 1967. Types 4 are in 12 volts, as they were only introduced to the market in the late 1960s.
alternator operating principle The direct current dynamo greatest asset turned out to be its greatest limitation, the collector. Supplying more current would shorten the life of the carbon brushes; something had to be found for that. So the dynamo no longer sufficed for the new situation of the mid-sixties.
dynamo operating principal Wouldn`t it be nice to know what DF means, for example? And what does D+ mean? If you know what`s behind these letters and numbers, then connecting the dynamo will be a breeze. In this article, we will explain the working principle of the dynamo, also known as a direct current generator.
voltage drops The electric consumers of your classic Volkswagen expect the full 6 volts or 12 volts (or more) to function properly, which is unfortunately not always the case. Especially the 6 volt version sometimes complains about slow running windscreen wipers, weak headlights and direction indicators that pinch too slowly.
measuring electric current To measure current, you must interrupt the circuit through which the current flows. The ammeter must be connected in series. Therefore, that a current clamp is a better solution. This type of ammeter does not affect the circuit to be measured, it measures the magnetic field around the conductor (induction principle, see edition 26).
crimp terminals Replacing the complete wiring loom seems the most obvious solution. We have them all in stock for every type of VW. But this is a very drastic job that you will probably only do when a total restoration is at hand. And, is it really always necessary?
replacing spade connectors A messy electrical connection will soon lead to the failure of electrical accessories or, in the worst case, the engine. Incorrect connections can also result in short-circuits, causing the wiring harness to burn out. Enough reasons to master a good technique to make the electrical connections of your VW neat and tidy.