Maskinvaresett for motormontering (10 mm sylinderbolter)
Oppmerksomhet: Alle norske bestillinger vil bli sendt av Winston VW Veteran AS (Sandnes, Norge),
så fraktkostnader er nå mye lavere og alle lokale avgifter er nå inkludert i prisen. På store karosserideler må det beregnes leveringstid, og høyere Innenlandsfrakt.
Delene som er nevnt her, har en nær sammenheng med den valgte delen og blir ofte bestilt sammen med den valgte delen eller søkt etter.
Tips: Hvis du ikke får et godt søkeresultat når du skriver inn et søkeord, prøv en del som har noe med det å gjøre, hvis det er en relatert fane, er den søkte delen ofte nevnt der.
Utstyrssett for kortblokk (10 mm sylinderbolter)
Type 1 Motorer (not 25hp+30hp)
Type 3 Motorer Artikkelnummer : 8006
Useful information from Paruzzi magazine and from our YouTube channel :
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.
Engine diagnostics - video 04 part 2 valves and valve springs In the second and third parts of this video, we will measure valve spring pressure. We begin in part 2 by measuring the valve spring pressure at open valve. Also known as the valve spring pressure at maximum valve lift. In part 3, we will measure the valve spring pressure at installed length.
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
Engine Overhaul - video 02 overhauled engines We show in this video all the engines that we overhauled for the video series. An AB 1300, an AS 1600, an AJ 1600 and a D 1200 engine, every step, every detail of the overhaul of these air-cooled Volkswagen engines will be discussed in this series.
the valve clearance explained The valves of the VW boxer engine ensure that the petrol air mixture can be fed into the cylinders (through the inlet valves), and that after compression this mixture can be discharged through the exhaust (exhaust valves). An accurate adjustment of the valves is of utmost importance for the proper functioning of your engine.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
Engine diagnostics - video 02 rockers and rocker arm In video fourteen of our engine overhaul video series, we disassembled and reassembled the rocker arms and rocker shaft. We will diagnose the rocker arms and rocker shaft in this video. Additional attention will be paid to the adjusting screws and adjusting nuts.
sump plate stud length How many VW enthusiasts are surprised that the engine leaks after an oil change? Read all about the type 1 sump plate in edition 20, what to look out for, how to attach it and with which tools. In this edition we will determine the maximum length of the sump plate studs, to prevent oil leaks.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.