Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Uudelleenrakennusmoottori 1775cc (uusi kotelo) ja ydintalletus
Type 1 moottori 1775cc
Note:
Price includes €370,-core deposit. Tuotenumero : 5546
Moottorin 1600cc (AD / AJ / AS) uudelleenkorjaus (uusi kotelo) ja ytimen talletus
Type 1 moottori 1600cc (moottoritcode AD, AJ or AS) dual port joissa 200 mm flywheel
Note:
Price includes €370,-core deposit. Tuotenumero : 5503 Alkuperäinen VW-numero : 211100033
€ 4670,00
Moottori rakennetaan asiakastilauksesta, jolloin toimitusaika on vähintään 12 viikkoa.
Useful information from Paruzzi magazine and from our YouTube channel :
removing the engine The air-cooled Volkswagen is an ingenious design, but not all work can be done with built-in engine, unfortunately. Sometimes it is also much more comfortable to work with the engine on the workbench hanging from an engine mount.
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
installing the engine In edition 16 we explained how to remove the engine of a VW Beetle, two techniques were discussed. The most important points of attention for the installation of the engine are indicated in this article. During the installation of the engine you will have to position the pilot shaft of the gearbox perfectly opposite the centre of the clutch.
replacing the sump plate studs If the studs are not tightened properly, it is practically impossible to tighten the crankcase sump plate to compress the paper gaskets. The infamous engine oil leak is the result, and no, it is not normal for an air-cooled VW to leak! A leaking engine will be rejected at the mandatory technical inspection.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
crankshaft pulley removal Removing the crankshaft pulley on an engine that has run 100,000 km and more is best not done with just a hammer and brute force. You would prefer to reuse the original crankshaft pulley on your engine, were it not for the budget, also for the factory originality.