Venttiilikopan tiiviste (per pari)
Type 1 moottori 1200cc (lukuunottamatta 25hp + 30hp)
Type 1 moottori 1300-1500-1600cc
Type 3 moottori
CT / CZ moottori
Waterboxer moottori Tuotenumero : 1956 Alkuperäinen VW-numero : 113101481F, 113101483D
Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Suuren välityssuhteen venttiilin säätöruuvit M8 (8 kpl)
Type 1-1983 (VIN 11-E-119 815)
Type 3
Type 4 1700cc
CT / CZ Tuotenumero : 3784
Keinuvivut 1:25-1 (8 kpl)
Type 1 8.1960 ja uudemmat
Karmann Ghia 8.1960 ja uudemmat
Bussi 12 / 13 / 15 / 1600cc 8.1960 ja uudemmat
TYP-2 T25 / T3 Tölkki Waterboxer moottori
Type 3
TYP 181 Tuotenumero : 1783
Useful information from Paruzzi magazine and from our YouTube channel :
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.
mesuring the compression How can you determine very objectively how much wear the engine has? An indication of the wear level can be obtained by performing a compression measurement, the engine compression determines the power of your VW. Anyone can perform a compression measurement on an air-cooled or water-cooled VW.
Engine diagnostics - video 04 part 2 valves and valve springs In the second and third parts of this video, we will measure valve spring pressure. We begin in part 2 by measuring the valve spring pressure at open valve. Also known as the valve spring pressure at maximum valve lift. In part 3, we will measure the valve spring pressure at installed length.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
Engine overhaul - video 16 part 1 valves removal In this first part of video 16, we disassemble cylinder head valves and valve springs. In the first part, we start by demonstrating the tools and techniques used, and disassemble the valves of a relatively new cylinder head.
oil consumption Oil leaks are easy to rectify, sometimes even without having to remove the motor. We have saved the more difficult cases for this article, so we did not call this "oil leaks part 2" but "oil consumption". The distinction between the two is sometimes difficult to make, hopefully the information that follows will bring clarity.
setting valve clearance The first technical work I ever did on my first Volkswagen Beetle was to set the valves. I didn't know much about the technology of the VW Beetle at the time, but I dared to do it, valve setting is easy to do yourself, you don't need many tools, and it's essential for the proper functioning of your classic.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
the valve clearance explained The valves of the VW boxer engine ensure that the petrol air mixture can be fed into the cylinders (through the inlet valves), and that after compression this mixture can be discharged through the exhaust (exhaust valves). An accurate adjustment of the valves is of utmost importance for the proper functioning of your engine.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.