Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Vaahto ilmansuodattimen patruuna
Height: 50 mm
Halkaisija: 135 mm
Fits air cleaner: #2148, #2152 ja #5121 Tuotenumero : 2147
Jos valittu osa ei sovi valitsemaasi VW-tyyppiin, tarkastele tältä listalta vastaavia osia jotka sopivat muihin vuosimalleihin tai muihin VW-tyyppeihin.
Ilmansuodatin, vakio
Type 1 8.1974 ja uudemmat
Type 4 8.1972 ja uudemmat
CT / CZ
Waterboxer moottori-7.1985 (1900cc DF kaikki vuosimallit) Tuotenumero : 42149 Alkuperäinen VW-numero : 021129620
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
fuel circuit - concept The combustion engine of our air-cooled Volkswagen uses a mixture of petrol and air. It is extremely important that both the amount of air and the purity of the air are regulated, this also applies to the petrol. Unfortunately, the petrol circuit is not very well known to enthusiasts and it is not always well maintained.
Engine overhaul - video 12 the flywheel In this video, we'll explain how to disassemble and assemble the flywheel, and what tools you'll need to do so. To disassemble the flywheel, you will need to unscrew the gland nut. This nut is attached with a torque of 350 Nm, it will require some force to loosen.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine diagnostics - video 04 part 1 valves and valve springs In video 16 of the engine overhaul series, we disassembled the valves and valve springs.
Not all of the cylinder heads we showed were in good condition, this does not mean that all parts need to be replaced. After a thorough diagnosis, it will show if the valves and valve springs are still reusable. This video discusses valve and valve spring diagnosis. It consists of four parts.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
Engine diagnostics - video 02 rockers and rocker arm In video fourteen of our engine overhaul video series, we disassembled and reassembled the rocker arms and rocker shaft. We will diagnose the rocker arms and rocker shaft in this video. Additional attention will be paid to the adjusting screws and adjusting nuts.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.