Kaross till chassi, horn, stötfångarfäste och motormonteringsbultar (4 delar)
Bubbla
Karmann Ghia till och med 7.1971
Bus 8.1967 till och med 7.1972
Type 3
Type 181
Specifications:
Thread size: M10 x 1.50
Length: 25 mm
Tensile load: 8.8
Material: blackened steel
Wrench size: 17 mm
Produktnummer : 7424 Original VW nummer : N102546, N102541, N102542, N102544, N01025414
Dessa delar levereras eller ingår i den del som du har valt nu, du kan använda dessa delar för att reparera den valda delen.
Bärarm lager (per styck)
Upper side:
Bubbla (excluded 1302 and 1303) 8.1960 (VIN 2 921 552) och senare
Karmann Ghia 8.1960 (VIN 2 921 552) och senare
Type 181
Lower side:
Bubbla 1960 (VIN 2 921 552) till och med 7.1965
Karmann Ghia 1960 (VIN 2 921 552) till och med 7.1965
Specifications:
Outer diameter: 46 mm Produktnummer : 3374 Original VW nummer : 111401301
Justerbultar för framaxel för Puma-sänkningssystem (per par)
front axles #1397, #1398, #3398 and #3399
lowering system #3397 and #23396 Produktnummer : 3402
Låsmuttrar för framaxelns justeringsbult för Puma sänksystem (4 st)
front axles #1397, #1398, #3398 and #3399
lowering system #3397 and #23396 Produktnummer : 3427
Varorna som visas här är relaterade till varandra med varan du valt och beställs eller söks ofta tillsammans.
Tips: får du ingen bra träff på sökordet du angivit så försök då att söka en vara som är relaterad till den. Finns det då en flik relaterade varor så kanske du hittar varan du sökte där.
Styrväxel
Bubbla:
Sedan export models 1961 (4 236 757) till och med 7.1965
VW 1200, VW 1300 and VW 1500 8.1965 och senare
Convertible 1961 (VIN 3 933 185) till och med 7/1970
Karmann Ghia 1961 (VIN 4 236 757) och senare
Type 3 all
Type 181 all
Note:
- Not filled with grease, use grease #50717
- For models till och med 7.1965 with sector Type steering box use also #4347 or #4354 Produktnummer : 1368 Original VW nummer : 113415061
Styrdämpare i lager
Bubbla (except 1302 and 1303) 1960 (VIN 2 921 552) och senare
Karmann Ghia 1960 (VIN 2 921 552) och senare
Type 181 Produktnummer : 1312 Original VW nummer : 113425021L, 113425021, 113415021A
Stötdämpare (olja) låga /par
Bubbla / Karmann Ghia 1952 och senare rear
Bubbla / Karmann Ghia 1952 till och med 7.1965 front
Bus till och med 7.1967 rear
Bus till och med 7.1979 front Produktnummer : 1356
Gasladdad stötdämpare med dubbla rör (låg) (varje)
Bubbla / Karmann Ghia 52 och senare rr
Bubbla / Karmann Ghia 52 till och med 7.1965 frt
Bus till och med 67 rr
Bus till och med 79 frt
Type 3 frt/rr
Type 181 rr Produktnummer : 1306
Framvagn standard
Bubbla 1960 (VIN 2 921 552) till och med 7.1965 LHD
Karmann Ghia 1960 (VIN 2 921 552) till och med 7.1965 LHD Produktnummer : 6395 Original VW nummer : 113401021A, 113401025A
Ifall varan du valt inte är tillämpningsbar på denna typ Volkswagen, finns alternativ med liknande varor som passar på andra årsmodeller eller andra fordonsmodeller.
Framvagn kortad 5 cm
Bubbla 1200-1300-1500 8.1965 och senare LHD
Karmann Ghia 8.1965 och senare LHD Produktnummer : 3399
Useful information from Paruzzi magazine and from our YouTube channel :
measuring rear wheel geometry In the previous edition of this series, we measured the wheel geometry of the front axle. In this edition, we will measure the wheel geometry of the rear axle. The adjustment of both front and rear axles will follow in the next edition.
wheel play adjustment The front and rear axles of your VW are mechanical parts that have to withstand a lot of forces. They are designed to withstand the full weight of the car, but they are also designed to absorb the forces that occur during acceleration and braking, which are several times greater than the weight of the car.
front wheel bearing replacement If the wheel bearings are worn or damaged, there is no point in adjusting the wheel play. You will first have to replace the wheel bearings to get a good result. In edition 18 we tuned the wheel play of the front wheels to the feel, in edition 19 we fine-tuned the wheel play by using a measuring clock. In edition 21, we are replacing the front wheel bearings.
Caster and Toe In the previous edition, we explained what Camber and King Pin Inclination (KPI) are. An important consequence of KPI is the Scrub Radius, which is the friction radius of the front wheels. In addition to Camber and KPI, there are other important parameters, such as Caster angle and Toe.
camber and King Pin The most visually striking of all wheel geometry settings, is wheel camber. We also discuss the King Pin Inclination and the Scrub radius in this article.
removing the MacPherson Sometimes it will be necessary to disassemble the MacPherson. It is located at the front on younger Volkswagen models such as the VW Beetles 1302 and 1303 and the VW Vanagon and at the front and rear on the VW Golf and VW 411/412. We will show how it works on a VW 1303, repair the bearings and install.
measuring front wheel geometry In this edition, we will explain how to measure front axle wheel geometry, and what the values are for each type of classic VW. Camber Angle, Toe and Caster are discussed in this edition. Measuring the rear axle is covered in edition 28, and in edition 29 we will show how to adjust front and rear axle wheel geometry.
the VW suspension Ferdinand Porsche came up with an ingenious concept at the beginning of the last century. A car that was built on the basis of a steel chassis plate with an independent and self-supporting body. Most of the cars from that period were built around a tubular chassis, so the Volkswagen Beetle (then still a Kdf-car) was revolutionary.
independent suspension Fixed one-piece front axles with leaf springs or torsion springs as on the VW Beetle, were widely used until the end of the sixties. Due to the demand for more comfort, better steering and by driving longer distances, the independent front suspension became more and more popular on luxury cars.