Passar till: Type 1 engines
Type 3 engines
CT/CZ engines
Specifications:
Stroke: 78 mm
Journal: VW Type 1
Material: 4340 chromoly
Fel:
-Middl bearing too large, 55.01
-Has been balanced
-Has been mounted but not rotated.
Vad är en Second Chance reservdel? En reservdel är en del som har returnerats av en kund och som inte längre kan säljas som ny eller som har skadats under transporten. Skador eller ofullständighet är de vanligaste defekterna. Felet beskrivs ovan och bilden är den verkliga representationen av den relevanta delen. Klicka på det ursprungliga Paruzzi-numret för mer information om delen och bilder på originaldelen.
Andrahandsdelar kan inte returneras och har inte någon form av garanti, men du får en trevlig rabatt på nypriset.
Useful information from Paruzzi magazine and from our YouTube channel :
oil consumption Oil leaks are easy to rectify, sometimes even without having to remove the motor. We have saved the more difficult cases for this article, so we did not call this "oil leaks part 2" but "oil consumption". The distinction between the two is sometimes difficult to make, hopefully the information that follows will bring clarity.
Engine overhaul - video 13 replacing the crank seal During a complete engine overhaul, you will need to replace the crank seal. But replacement may also be necessary, when you discover an oil leak behind the flywheel, which will impair the operation of the clutch. We show in this video how to disassemble and reassemble the crank seal.
Engine overhaul - video 11 the clutch To disassemble the flywheel, you will need to loosen the gland nut, we discuss that in video 12. But first you will need to disassemble the clutch. You can do that when the engine is on the workbench, or hanging from an engine mount. In this video we show various techniques and tools to disassemble the clutch of your Type 1 Volkswagen engine without damage.
measure crankshaft end play The play is caused by wear of the engine, this is actually very normal, and will occur faster with performance engines. With normal use of standard VW engines in combination with a good maintenance of the engine, wear will not occur quickly.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
Engine diagnostics - video 04 part 2 valves and valve springs In the second and third parts of this video, we will measure valve spring pressure. We begin in part 2 by measuring the valve spring pressure at open valve. Also known as the valve spring pressure at maximum valve lift. In part 3, we will measure the valve spring pressure at installed length.
Engine diagnostics - video 03 pushrods In video fourteen of our series on engine overhaul, we disassembled and reassembled the rocker arms and pushrods. In this video, we will inspect the pushrods. The result of this diagnosis, will tell us if we can reinsert the pushrods, or if we need to replace them.
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.