Venttiilikopan tiiviste (per pari)
Type 1 moottori 1200cc (lukuunottamatta 25hp + 30hp)
Type 1 moottori 1300-1500-1600cc
Type 3 moottori
CT / CZ moottori
Waterboxer moottori Tuotenumero : 1956 Alkuperäinen VW-numero : 113101481F, 113101483D
Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Suuren välityssuhteen venttiilin säätöruuvit M8 (8 kpl)
Type 1-1983 (VIN 11-E-119 815)
Type 3
Type 4 1700cc
CT / CZ Tuotenumero : 3784
Keinuvivut 1:25-1 (8 kpl)
Type 1 8.1960 ja uudemmat
Karmann Ghia 8.1960 ja uudemmat
Bussi 12 / 13 / 15 / 1600cc 8.1960 ja uudemmat
TYP-2 T25 / T3 Tölkki Waterboxer moottori
Type 3
TYP 181 Tuotenumero : 1783
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
mesuring the compression How can you determine very objectively how much wear the engine has? An indication of the wear level can be obtained by performing a compression measurement, the engine compression determines the power of your VW. Anyone can perform a compression measurement on an air-cooled or water-cooled VW.
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine overhaul - video 11 the clutch To disassemble the flywheel, you will need to loosen the gland nut, we discuss that in video 12. But first you will need to disassemble the clutch. You can do that when the engine is on the workbench, or hanging from an engine mount. In this video we show various techniques and tools to disassemble the clutch of your Type 1 Volkswagen engine without damage.
Engine overhaul - video 15 disassemble cylinder heads In this video, we will show how to disassemble the cylinder heads of a VW Type 1 engine, and what challenges you may face.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?
Engine diagnostics - video 04 part 1 valves and valve springs In video 16 of the engine overhaul series, we disassembled the valves and valve springs.
Not all of the cylinder heads we showed were in good condition, this does not mean that all parts need to be replaced. After a thorough diagnosis, it will show if the valves and valve springs are still reusable. This video discusses valve and valve spring diagnosis. It consists of four parts.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.