Venttiilikopan tiiviste (per pari)
Type 1 moottori 1200cc (lukuunottamatta 25hp + 30hp)
Type 1 moottori 1300-1500-1600cc
Type 3 moottori
CT / CZ moottori
Waterboxer moottori Tuotenumero : 1956 Alkuperäinen VW-numero : 113101481F, 113101483D
Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Keinuvivun jousen aluslevyt (4 kpl)
Type 1 moottori lukuunottamatta 25hp + 30hp
Type 3 moottori
CT / CZ moottori
specifications:
Thickness: 0.5 mm
Inner size: 18.6 mm
Outer size: 25.0 mm Tuotenumero : 3779 Alkuperäinen VW-numero : 113109437
Keinuvivustoakselin lukko, 4kpl
Type 1 (lukuunottamatta 25hp + 30hp)
Type 3 kaikki
CT kaikki
Waterboxer moottori kaikki Tuotenumero : 3786 Alkuperäinen VW-numero : 113109439
Useful information from Paruzzi magazine and from our YouTube channel :
oil consumption Oil leaks are easy to rectify, sometimes even without having to remove the motor. We have saved the more difficult cases for this article, so we did not call this "oil leaks part 2" but "oil consumption". The distinction between the two is sometimes difficult to make, hopefully the information that follows will bring clarity.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
Engine overhaul - video 03 the workshop We show in this video what the possibilities are to work on your VW engine. If you plan to overhaul several engines, then buying a professional engine stand is recommended. If you only want to overhaul the engine of your own classic Volkswagen, then buying special tools is not cost effective. We will show all options.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine overhaul - video 15 disassemble cylinder heads In this video, we will show how to disassemble the cylinder heads of a VW Type 1 engine, and what challenges you may face.
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
the valve clearance explained The valves of the VW boxer engine ensure that the petrol air mixture can be fed into the cylinders (through the inlet valves), and that after compression this mixture can be discharged through the exhaust (exhaust valves). An accurate adjustment of the valves is of utmost importance for the proper functioning of your engine.
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.