Aplicável: Type 1 motores 8.1969 e mais tarde
Type 3 motores 8.1969 e mais tarde
Referência Paruzzi:
03993
€ 99,92 excluindo IVA € 120.9 incluindo IVA
Em stock: 2 Encomende antes das 14:00 CET de Segunda a Sexta e enviamos no próprio dia.. Mais tarde do que normal devido a férias públicas Serão enviados via UPS
As peças aqui mencionadas têm uma relação forte com a peça seleccionada e são frequentemente encomendadas juntamente com a peça seleccionada ou procuradas. Tip: Se não receber um bom resultado de busca quando entrar numa palavra-chave, tenta uma parte que tenha algo a ver com ela, se existe uma lista relatada, o item revistado é frequentemente mencionado lá
Radiador de óleo com ventilador eléctrica
280 x 260 x 40 mm
12V / 80 watt Referência Paruzzi : 1976
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
type 1 sump plate Replacing the crankcase oil of a Type 1 engine is a job every VW enthusiast has done once in a while. It involves loosening a few nuts, replacing gaskets and tightening everything again, right?
It seems a simple operation, but nothing could be further from the truth.
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
Engine overhaul - video 12 the flywheel In this video, we'll explain how to disassemble and assemble the flywheel, and what tools you'll need to do so. To disassemble the flywheel, you will need to unscrew the gland nut. This nut is attached with a torque of 350 Nm, it will require some force to loosen.
Engine overhaul - video 16 part 1 valves removal In this first part of video 16, we disassemble cylinder head valves and valve springs. In the first part, we start by demonstrating the tools and techniques used, and disassemble the valves of a relatively new cylinder head.
Engine overhaul - video 11 the clutch To disassemble the flywheel, you will need to loosen the gland nut, we discuss that in video 12. But first you will need to disassemble the clutch. You can do that when the engine is on the workbench, or hanging from an engine mount. In this video we show various techniques and tools to disassemble the clutch of your Type 1 Volkswagen engine without damage.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.