Oppmerksomhet: Alle norske bestillinger vil bli sendt av Winston VW Veteran AS (Sandnes, Norge),
så fraktkostnader er nå mye lavere og alle lokale avgifter er nå inkludert i prisen. På store karosserideler må det beregnes leveringstid, og høyere Innenlandsfrakt.
Delene som er nevnt her, har en nær sammenheng med den valgte delen og blir ofte bestilt sammen med den valgte delen eller søkt etter.
Tips: Hvis du ikke får et godt søkeresultat når du skriver inn et søkeord, prøv en del som har noe med det å gjøre, hvis det er en relatert fane, er den søkte delen ofte nevnt der.
Bremse rens (spray)
Content: 500 ml Artikkelnummer : 50150
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine diagnostics - video 04 part 1 valves and valve springs In video 16 of the engine overhaul series, we disassembled the valves and valve springs.
Not all of the cylinder heads we showed were in good condition, this does not mean that all parts need to be replaced. After a thorough diagnosis, it will show if the valves and valve springs are still reusable. This video discusses valve and valve spring diagnosis. It consists of four parts.
measure crankshaft end play The play is caused by wear of the engine, this is actually very normal, and will occur faster with performance engines. With normal use of standard VW engines in combination with a good maintenance of the engine, wear will not occur quickly.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
Engine diagnostics - video 02 rockers and rocker arm In video fourteen of our engine overhaul video series, we disassembled and reassembled the rocker arms and rocker shaft. We will diagnose the rocker arms and rocker shaft in this video. Additional attention will be paid to the adjusting screws and adjusting nuts.
the clutch: basic concept For a long time I wondered how the clutch in our Volkswagen Fastback worked, I was only six years old. I didn't understand very well that by releasing a pedal our VW started to drive spontaneously. Well, if you understand how disc brakes work, then the step to understanding how the clutch mechanism works is not far.