As peças aqui mencionadas têm uma relação forte com a peça seleccionada e são frequentemente encomendadas juntamente com a peça seleccionada ou procuradas. Tip: Se não receber um bom resultado de busca quando entrar numa palavra-chave, tenta uma parte que tenha algo a ver com ela, se existe uma lista relatada, o item revistado é frequentemente mencionado lá
Mangueira para gasolina de tecido entrançado (por metro)
Diâmetro interior: 4.10 (max. 4.60 mm)
Diâmetro exterior: 9.15 (max. 9.65 mm)
Working pressure: 7.5 bar
Bursting pressure: 30 bar
Nota:
Approved for fossil leaded e unleaded petrol E5, E10, E15, E85 e diesel. Referência Paruzzi : 4152 Referencia VW original : N10196502
Estas peças podem oferecer uma alternativa à parte seleccionada, por exemplo, uma qualidade, cor, variação diferente, etc.
Mangueira de respiração com um exterior têxtil (por metro)
Diâmetro interior: 12 mm
Diâmetro exterior: 17 mm
Working pressure: 7 bar
Bursting pressure: 30 bar
Nota:
Approved for fossil leaded e unleaded petrol E5, E10, E15, E85 e diesel. Referência Paruzzi : 3975 Referencia VW original : N0202903, N203741, N0203741
Mangueira para óleo com revestimento exterior em aço inoxidável entrançado (por metro)
Diâmetro interior: 12.7 mm
Diâmetro exterior: 17 mm Referência Paruzzi : 988
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
Engine Overhaul - video 02 overhauled engines We show in this video all the engines that we overhauled for the video series. An AB 1300, an AS 1600, an AJ 1600 and a D 1200 engine, every step, every detail of the overhaul of these air-cooled Volkswagen engines will be discussed in this series.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
oil consumption Oil leaks are easy to rectify, sometimes even without having to remove the motor. We have saved the more difficult cases for this article, so we did not call this "oil leaks part 2" but "oil consumption". The distinction between the two is sometimes difficult to make, hopefully the information that follows will bring clarity.