Oppmerksomhet: Alle norske bestillinger vil bli sendt av Winston VW Veteran AS (Sandnes, Norge),
så fraktkostnader er nå mye lavere og alle lokale avgifter er nå inkludert i prisen. På store karosserideler må det beregnes leveringstid, og høyere Innenlandsfrakt.
Disse delene bestilles vanligvis sammen med den valgte delen. De er ikke inkludert i leveransen, men byttes ofte ut sammen.
Standard oljepåfyllingslokk
Type 1 Motorer 8.1955 til 9.1992 (except injection Motorer with Motorercode AJ) Artikkelnummer : 3883 Original VW nummer : 111115485
Delene som er nevnt her, har en nær sammenheng med den valgte delen og blir ofte bestilt sammen med den valgte delen eller søkt etter.
Tips: Hvis du ikke får et godt søkeresultat når du skriver inn et søkeord, prøv en del som har noe med det å gjøre, hvis det er en relatert fane, er den søkte delen ofte nevnt der.
Mutter for oljepåfylling
Type 1 / Karmann Ghia 8.1960 og senere (not 30hp)
Buss 12/13/15/1600 8.1960 og senere (not 30hp + CT)
Type 181 Artikkelnummer : 1872 Original VW nummer : 113115495
Useful information from Paruzzi magazine and from our YouTube channel :
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
Engine overhaul - video 16 part 2 valves removal In Part 1, we showed the basic techniques for disassembling the valves and valve springs. We did this on a fairly new cylinder head.
When you`re dealing with a used cylinder head, disassembly may be a little less smooth.
Engine diagnostics - video 03 pushrods In video fourteen of our series on engine overhaul, we disassembled and reassembled the rocker arms and pushrods. In this video, we will inspect the pushrods. The result of this diagnosis, will tell us if we can reinsert the pushrods, or if we need to replace them.
Engine overhaul - video 11 the clutch To disassemble the flywheel, you will need to loosen the gland nut, we discuss that in video 12. But first you will need to disassemble the clutch. You can do that when the engine is on the workbench, or hanging from an engine mount. In this video we show various techniques and tools to disassemble the clutch of your Type 1 Volkswagen engine without damage.
Engine Overhaul - video 02 overhauled engines We show in this video all the engines that we overhauled for the video series. An AB 1300, an AS 1600, an AJ 1600 and a D 1200 engine, every step, every detail of the overhaul of these air-cooled Volkswagen engines will be discussed in this series.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?