Sopii malleihin: Type 1 moottori 1200cc 1980 (D 1 455 272) ja uudemmat
Type 1 moottori 1500cc
Type 1 moottori 1600cc (Bussi-1975 VIN 216 2118 505)
Type 3 moottori 8.1962 ja uudemmat
Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Puhdistusspray
Content: 500 ml Tuotenumero : 50150
Useful information from Paruzzi magazine and from our YouTube channel :
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
Engine overhaul - video 03 the workshop We show in this video what the possibilities are to work on your VW engine. If you plan to overhaul several engines, then buying a professional engine stand is recommended. If you only want to overhaul the engine of your own classic Volkswagen, then buying special tools is not cost effective. We will show all options.
crankshaft seal replacement If you find that the crankshaft clearance is outside the factory specifications, replacing the crankshaft seal will not be a solution for the oil leak you have identified. If the crankshaft clearance is less than 0.30 mm, it makes sense to replace the oil seal, otherwise a total engine overhaul is the only worthwhile option.
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine Overhaul - video 02 overhauled engines We show in this video all the engines that we overhauled for the video series. An AB 1300, an AS 1600, an AJ 1600 and a D 1200 engine, every step, every detail of the overhaul of these air-cooled Volkswagen engines will be discussed in this series.