Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Polttoaineletku, kangasvahvisteinen (per metri)
Inner diameter: 4.10 (max. 4.60 mm)
Outer diameter: 9.15 (max. 9.65 mm)
Working pressure: 7.5 bar
Bursting pressure: 30 bar
Note:
Hyväksytty lyijyttömille ja lyijylisäaineellisille posttoaineille E5, E10, E15, E85 ja diesel. Tuotenumero : 4152 Alkuperäinen VW-numero : N10196502
Polttoaineletku, kangasvahvisteinen, metri
Inner diameter: 6.00 (max. 6.50 mm)
Outer diameter: 11.70 (max. 12.20 mm)
Working pressure: 7.5 bar
Bursting pressure: 30 bar
Note:
Hyväksytty lyijyttömille ja lyijylisäaineellisille posttoaineille E5, E10, E15, E85 ja diesel. Tuotenumero : 1152 Alkuperäinen VW-numero : N10120701
Polttoaineletku, kangasvahvisteinen, metri
Inner diameter: 8.00 (max. 8.50 mm)
Outer diameter: 13.70 (max. 14.20 mm)
Working pressure: 7.5 bar
Bursting pressure: 30 bar
Note:
Hyväksytty lyijyttömille ja lyijylisäaineellisille posttoaineille E5, E10, E15, E85 ja diesel. Tuotenumero : 981 Alkuperäinen VW-numero : N90170001, N0201302
Nämä ovat vaihtoehtoisia tuotteita valitsemallesi osalle, esimerkiksi eri laatuisia, hintaisia, värisiä jne.
Hengitysletku, jonka ulkopuoli on tekstiiliainetta (metriä kohti)
Inner diameter: 12 mm
Outer diameter: 17 mm
Working pressure: 7 bar
Bursting pressure: 30 bar
Note:
Hyväksytty lyijyttömille ja lyijylisäaineellisille posttoaineille E5, E10, E15, E85 ja diesel. Tuotenumero : 3975 Alkuperäinen VW-numero : N0202903, N203741, N0203741
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 12 the flywheel In this video, we'll explain how to disassemble and assemble the flywheel, and what tools you'll need to do so. To disassemble the flywheel, you will need to unscrew the gland nut. This nut is attached with a torque of 350 Nm, it will require some force to loosen.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
Engine overhaul - video 03 the workshop We show in this video what the possibilities are to work on your VW engine. If you plan to overhaul several engines, then buying a professional engine stand is recommended. If you only want to overhaul the engine of your own classic Volkswagen, then buying special tools is not cost effective. We will show all options.
Engine Overhaul - video 02 overhauled engines We show in this video all the engines that we overhauled for the video series. An AB 1300, an AS 1600, an AJ 1600 and a D 1200 engine, every step, every detail of the overhaul of these air-cooled Volkswagen engines will be discussed in this series.
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine Overhaul - video 01 video series preview In this video, we will give an overview of the most important steps during the engine overhaul of a type 1 air-cooled Volkswagen engine. Each step will be discussed in a separate video. We will show special tools and even homemade tools to help the enthusiast perform their engine overhaul.