Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Moottorin uudelleenkorjaus 1641cc W-110 (uusi kotelo) ja ytimen talletus
Type 1 moottori 1641cc joissa W-110 camshaft
Note:
Price includes €370,-core deposit. Tuotenumero : 5545
Moottorin 1600cc (AD / AJ / AS) uudelleenkorjaus (uusi kotelo) ja ytimen talletus
Type 1 moottori 1600cc (moottoritcode AD, AJ or AS) dual port joissa 200 mm flywheel
Note:
Price includes €370,-core deposit. Tuotenumero : 5503 Alkuperäinen VW-numero : 211100033
€ 4670,00
Moottori rakennetaan asiakastilauksesta, jolloin toimitusaika on vähintään 12 viikkoa.
Useful information from Paruzzi magazine and from our YouTube channel :
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine Overhaul - video 01 video series preview In this video, we will give an overview of the most important steps during the engine overhaul of a type 1 air-cooled Volkswagen engine. Each step will be discussed in a separate video. We will show special tools and even homemade tools to help the enthusiast perform their engine overhaul.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
type 1 sump plate Replacing the crankcase oil of a Type 1 engine is a job every VW enthusiast has done once in a while. It involves loosening a few nuts, replacing gaskets and tightening everything again, right?
It seems a simple operation, but nothing could be further from the truth.
oil pressure gauge After an engine rebuild, when you start the engine for the first time, and when you start driving, you need to keep a close eye on a number of engine parameters. The most important are oil pressure, engine oil temperature and cylinder head temperature.
remove a threaded stud While working on old-timers, you may come across a situation where you think "how can I solve that?". In my case, I was looking for a solution to loosen a stuck threaded rod, without damaging it.
Engine diagnostics - video 02 rockers and rocker arm In video fourteen of our engine overhaul video series, we disassembled and reassembled the rocker arms and rocker shaft. We will diagnose the rocker arms and rocker shaft in this video. Additional attention will be paid to the adjusting screws and adjusting nuts.
Engine overhaul - video 15 disassemble cylinder heads In this video, we will show how to disassemble the cylinder heads of a VW Type 1 engine, and what challenges you may face.