Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta.
Venttiilien lash capit, 8kpl
Type 1 moottori (lukuunottamatta 25hp + 30hp)
Type 3 moottori
CT / CZ moottori
Type 4 moottori
Waterboxer moottori Tuotenumero : 1739
Työntötangon suojaputkien tiivisteet, silikoni, 16 kpl
Type 1 moottori lukuunottamatta 25hp + 30hp
Type 3 moottori
CT / CZ moottori the cylinder head puoli
Waterboxer moottori the cylinder head puoli Tuotenumero : 1751
Venttiilikopan tiiviste (per pari)
Type 1 moottori 1200cc (lukuunottamatta 25hp + 30hp)
Type 1 moottori 1300-1500-1600cc
Type 3 moottori
CT / CZ moottori
Waterboxer moottori Tuotenumero : 1956 Alkuperäinen VW-numero : 113101481F, 113101483D
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Type 1 engine mount In this article we show how to mount the engine of a VW Beetle or Karmann Ghia, so it becomes clear what to look out for when you mount the engine and build it back in.
oil consumption Oil leaks are easy to rectify, sometimes even without having to remove the motor. We have saved the more difficult cases for this article, so we did not call this "oil leaks part 2" but "oil consumption". The distinction between the two is sometimes difficult to make, hopefully the information that follows will bring clarity.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
crankshaft end play Whether an oil leak is caused by a defective crankshaft seal or O-ring/packaging is not always easy to determine. At the bottom of the engine, near the flywheel, where the gearbox and the engine are connected to each other, you will see traces of engine oil.
the valve clearance explained The valves of the VW boxer engine ensure that the petrol air mixture can be fed into the cylinders (through the inlet valves), and that after compression this mixture can be discharged through the exhaust (exhaust valves). An accurate adjustment of the valves is of utmost importance for the proper functioning of your engine.
Engine diagnostics - video 04 part 1 valves and valve springs In video 16 of the engine overhaul series, we disassembled the valves and valve springs.
Not all of the cylinder heads we showed were in good condition, this does not mean that all parts need to be replaced. After a thorough diagnosis, it will show if the valves and valve springs are still reusable. This video discusses valve and valve spring diagnosis. It consists of four parts.
installing the engine In edition 16 we explained how to remove the engine of a VW Beetle, two techniques were discussed. The most important points of attention for the installation of the engine are indicated in this article. During the installation of the engine you will have to position the pilot shaft of the gearbox perfectly opposite the centre of the clutch.
setting valve clearance The first technical work I ever did on my first Volkswagen Beetle was to set the valves. I didn't know much about the technology of the VW Beetle at the time, but I dared to do it, valve setting is easy to do yourself, you don't need many tools, and it's essential for the proper functioning of your classic.