Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Lohkon pinnapulttisarja, M8
Type 1 dual port moottori
CT / CZ moottori
specifications:
9 x 237 mm
3 x 202 mm
4 x 185 mm
16 x nuts M8
16 x washers 8.4 x 21 x 4 mm Tuotenumero : 1660 Alkuperäinen VW-numero : 043198035
Useful information from Paruzzi magazine and from our YouTube channel :
crankshaft seal replacement If you find that the crankshaft clearance is outside the factory specifications, replacing the crankshaft seal will not be a solution for the oil leak you have identified. If the crankshaft clearance is less than 0.30 mm, it makes sense to replace the oil seal, otherwise a total engine overhaul is the only worthwhile option.
measure crankshaft end play The play is caused by wear of the engine, this is actually very normal, and will occur faster with performance engines. With normal use of standard VW engines in combination with a good maintenance of the engine, wear will not occur quickly.
cylinder head specifications One of the most heavily loaded parts in the air-cooled VW engine is undoubtedly the cylinder head. Especially the valves, valve guides and valve seats have to endure a lot because of the high temperatures, the temperature differences and the mechanical load in an air-cooled engine.
oil pressure gauge After an engine rebuild, when you start the engine for the first time, and when you start driving, you need to keep a close eye on a number of engine parameters. The most important are oil pressure, engine oil temperature and cylinder head temperature.
Engine overhaul - video 16 part 1 valves removal In this first part of video 16, we disassemble cylinder head valves and valve springs. In the first part, we start by demonstrating the tools and techniques used, and disassemble the valves of a relatively new cylinder head.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
Engine diagnostics - video 04 part 1 valves and valve springs In video 16 of the engine overhaul series, we disassembled the valves and valve springs.
Not all of the cylinder heads we showed were in good condition, this does not mean that all parts need to be replaced. After a thorough diagnosis, it will show if the valves and valve springs are still reusable. This video discusses valve and valve spring diagnosis. It consists of four parts.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.