Do you have the product from the page mounted on your car? Take a clear picture or video of it and put it in the spotlights. This way your car gets admired by a lot of people and others can see what the product looks like. We reward your effort with a € 1,- discount code for every approved photo or video. Use the discount on your next order. Click here to upload your photo Click here to upload your video
The parts mentioned here have a close relationship with the selected part and are often ordered along with the selected part or searched for.
Tip: if you do not get a good search result when entering a keyword try a part that has something to do with it, if there is a related tab, the searched item is often mentioned there.
Brake and clutch cleaner
Content: 500 ml Paruzzi number : 50150
Useful information from Paruzzi magazine and from our YouTube channel :
oil consumption Oil leaks are easy to rectify, sometimes even without having to remove the motor. We have saved the more difficult cases for this article, so we did not call this "oil leaks part 2" but "oil consumption". The distinction between the two is sometimes difficult to make, hopefully the information that follows will bring clarity.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
Engine overhaul - video 16 part 2 valves removal In Part 1, we showed the basic techniques for disassembling the valves and valve springs. We did this on a fairly new cylinder head.
When you`re dealing with a used cylinder head, disassembly may be a little less smooth.
Engine Overhaul - video 01 video series preview In this video, we will give an overview of the most important steps during the engine overhaul of a type 1 air-cooled Volkswagen engine. Each step will be discussed in a separate video. We will show special tools and even homemade tools to help the enthusiast perform their engine overhaul.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine diagnostics - video 02 rockers and rocker arm In video fourteen of our engine overhaul video series, we disassembled and reassembled the rocker arms and rocker shaft. We will diagnose the rocker arms and rocker shaft in this video. Additional attention will be paid to the adjusting screws and adjusting nuts.
Engine overhaul - video 03 the workshop We show in this video what the possibilities are to work on your VW engine. If you plan to overhaul several engines, then buying a professional engine stand is recommended. If you only want to overhaul the engine of your own classic Volkswagen, then buying special tools is not cost effective. We will show all options.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
crankshaft seal replacement If you find that the crankshaft clearance is outside the factory specifications, replacing the crankshaft seal will not be a solution for the oil leak you have identified. If the crankshaft clearance is less than 0.30 mm, it makes sense to replace the oil seal, otherwise a total engine overhaul is the only worthwhile option.