Do you have the product from the page mounted on your car? Take a clear picture or video of it and put it in the spotlights. This way your car gets admired by a lot of people and others can see what the product looks like. We reward your effort with a € 1,- discount code for every approved photo or video. Use the discount on your next order. Click here to upload your photo Click here to upload your video
Fits: Type-1 8.1960 and later
Karmann Ghia 8.1960 and later
Bus 1200/1300/1500/1600cc 8.1960 and later
Vanagon/T25 Waterboxer engines
Type-3
Thing
Paruzzi number:
01783
€ 126,69 excluding VAT € 153.3 including VAT
in stock: 7 Order before 14:00 CET on Monday through Friday and we ship the same day. Will be sent via UPS
The parts mentioned here have a close relationship with the selected part and are often ordered along with the selected part or searched for.
Tip: if you do not get a good search result when entering a keyword try a part that has something to do with it, if there is a related tab, the searched item is often mentioned there.
Assembly lube, tube
Content: 7 gram Paruzzi number : 50890
Engine overhaul - video 12 the flywheel In this video, we'll explain how to disassemble and assemble the flywheel, and what tools you'll need to do so. To disassemble the flywheel, you will need to unscrew the gland nut. This nut is attached with a torque of 350 Nm, it will require some force to loosen.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine diagnostics - video 04 part 1 valves and valve springs In video 16 of the engine overhaul series, we disassembled the valves and valve springs.
Not all of the cylinder heads we showed were in good condition, this does not mean that all parts need to be replaced. After a thorough diagnosis, it will show if the valves and valve springs are still reusable. This video discusses valve and valve spring diagnosis. It consists of four parts.
Engine Overhaul - video 01 video series preview In this video, we will give an overview of the most important steps during the engine overhaul of a type 1 air-cooled Volkswagen engine. Each step will be discussed in a separate video. We will show special tools and even homemade tools to help the enthusiast perform their engine overhaul.
finding the top dead center What does Top Dead Center (TDC) actually mean? If you study the theory of the operation of an internal combustion engine - or the "petrol engine" - it will become clear. Without going into too much detail about the theory, we have to talk about the otto cycle, better known as the four stroke cycle.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.