Do you have the product from the page mounted on your car? Take a clear picture or video of it and put it in the spotlights. This way your car gets admired by a lot of people and others can see what the product looks like. We reward your effort with a € 1,- discount code for every approved photo or video. Use the discount on your next order. Click here to upload your photo Click here to upload your video
Fits: Type-4 engines
Defect(s):
-Set included only 1 valve cover without seals
What is a second chance part? A second chance part is a part that has been returned by a customer and can no longer be sold as new or it has suffered damage during transport. Damage or incompleteness are the most common defects. The defect is described above and the image is the true representation of the relevant part. Click on the original Paruzzi number for more information about the part and images of the original part.
Second chance parts can not be returned and do not have any form of warranty, but you will benefit from a pleasant discount on the new price.
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 16 part 2 valves removal In Part 1, we showed the basic techniques for disassembling the valves and valve springs. We did this on a fairly new cylinder head.
When you`re dealing with a used cylinder head, disassembly may be a little less smooth.
the valve clearance explained The valves of the VW boxer engine ensure that the petrol air mixture can be fed into the cylinders (through the inlet valves), and that after compression this mixture can be discharged through the exhaust (exhaust valves). An accurate adjustment of the valves is of utmost importance for the proper functioning of your engine.
Engine diagnostics - video 04 part 2 valves and valve springs In the second and third parts of this video, we will measure valve spring pressure. We begin in part 2 by measuring the valve spring pressure at open valve. Also known as the valve spring pressure at maximum valve lift. In part 3, we will measure the valve spring pressure at installed length.
installing the engine In edition 16 we explained how to remove the engine of a VW Beetle, two techniques were discussed. The most important points of attention for the installation of the engine are indicated in this article. During the installation of the engine you will have to position the pilot shaft of the gearbox perfectly opposite the centre of the clutch.
mesuring the compression How can you determine very objectively how much wear the engine has? An indication of the wear level can be obtained by performing a compression measurement, the engine compression determines the power of your VW. Anyone can perform a compression measurement on an air-cooled or water-cooled VW.
replace a thread When you are working on your VW, you will encounter this problem at some point; a bolt of the crankcase cover doesn't really turn in the thread in the crankcase anymore. The more you try, the worse it gets. There is too little tension between the crankcase cover and crankcase, with oil leakage as a result.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
crankshaft seal replacement If you find that the crankshaft clearance is outside the factory specifications, replacing the crankshaft seal will not be a solution for the oil leak you have identified. If the crankshaft clearance is less than 0.30 mm, it makes sense to replace the oil seal, otherwise a total engine overhaul is the only worthwhile option.