Dessa varor beställs ofta som tillval till varan du valt. De levereras alltså inte automatiskt med varan, men byts ofta tillsammans.
SI 5926 blå silikon tätningsmassa
Content: 40 ml
Color: blue
Chemical Type: Acetoxy Silicone
Maximum sealing gap: 1.0 mm
Temperature range: -54 °C to +150 °C Produktnummer : 50555
Varorna som visas här är relaterade till varandra med varan du valt och beställs eller söks ofta tillsammans.
Tips: får du ingen bra träff på sökordet du angivit så försök då att söka en vara som är relaterad till den. Finns det då en flik relaterade varor så kanske du hittar varan du sökte där.
Extra oljesump 0,95 liter med ``Lifetime`` filter
Type 1 (except 25hp+30hp)
Type 3
CT/CZ Produktnummer : 1884
Useful information from Paruzzi magazine and from our YouTube channel :
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine overhaul - video 16 part 1 valves removal In this first part of video 16, we disassemble cylinder head valves and valve springs. In the first part, we start by demonstrating the tools and techniques used, and disassemble the valves of a relatively new cylinder head.
Engine overhaul - video 13 replacing the crank seal During a complete engine overhaul, you will need to replace the crank seal. But replacement may also be necessary, when you discover an oil leak behind the flywheel, which will impair the operation of the clutch. We show in this video how to disassemble and reassemble the crank seal.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
Engine overhaul - video 12 the flywheel In this video, we'll explain how to disassemble and assemble the flywheel, and what tools you'll need to do so. To disassemble the flywheel, you will need to unscrew the gland nut. This nut is attached with a torque of 350 Nm, it will require some force to loosen.
Engine diagnostics - video 04 part 1 valves and valve springs In video 16 of the engine overhaul series, we disassembled the valves and valve springs.
Not all of the cylinder heads we showed were in good condition, this does not mean that all parts need to be replaced. After a thorough diagnosis, it will show if the valves and valve springs are still reusable. This video discusses valve and valve spring diagnosis. It consists of four parts.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine diagnostics - video 02 rockers and rocker arm In video fourteen of our engine overhaul video series, we disassembled and reassembled the rocker arms and rocker shaft. We will diagnose the rocker arms and rocker shaft in this video. Additional attention will be paid to the adjusting screws and adjusting nuts.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.