Passar till: Bubbla 1300, 1302, 1303 8.1970 och senare
Bubbla 1200 1972 (VIN 112 2670 583) och senare
Karmann Ghia 8.1970 och senare
Bus 8.1970 och senare
Type 3 8.1970 och senare
Type 181 8.1971 och senare
Varorna som visas här är relaterade till varandra med varan du valt och beställs eller söks ofta tillsammans.
Tips: får du ingen bra träff på sökordet du angivit så försök då att söka en vara som är relaterad till den. Finns det då en flik relaterade varor så kanske du hittar varan du sökte där.
Styrhylsa urtrampningslager
Bubbla 1300-1302-1303 8.1970 och senare
Bubbla 1200 1972 (112 2670 583) och senare
Karmann Ghia 8.1970 och senare
Bus 8.1970 och senare
Type 3 8.1970 och senare
Type 181 8.1971 och senare Produktnummer : 1522 Original VW nummer : 113141181A, 016141181
Ifall varan du valt inte är tillämpningsbar på denna typ Volkswagen, finns alternativ med liknande varor som passar på andra årsmodeller eller andra fordonsmodeller.
Urtrampningslager
Bubbla 1300, 1500 till och med 7.1970
Bubbla 1200 till och med 1972 (VIN 112 2670 582)
Karmann Ghia till och med 7.1970
Bus till och med 7.1970
Type 3 till och med 7.1970
Type 181 till och med 7.1971 Produktnummer : 1520 Original VW nummer : 111141165A, 111141167C
Urtrampningslager
Bubbla 1300, 1500 till och med 7.1970
Bubbla 1200 till och med 1972 (VIN 112 2670 582)
Karmann Ghia till och med 7.1970
Bus till och med 7.1970
Type 3 till och med 7.1970
Type 181 till och med 7.1971 Produktnummer : 1520 Original VW nummer : 111141165A, 111141167C
Urtrampningslager
Bubbla 1300, 1500 till och med 7.1970
Bubbla 1200 till och med 1972 (VIN 112 2670 582)
Karmann Ghia till och med 7.1970
Bus till och med 7.1970
Type 3 till och med 7.1970
Type 181 till och med 7.1971 Produktnummer : 1520 Original VW nummer : 111141165A, 111141167C
Urtrampningslager
Bubbla 1300, 1500 till och med 7.1970
Bubbla 1200 till och med 1972 (VIN 112 2670 582)
Karmann Ghia till och med 7.1970
Bus till och med 7.1970
Type 3 till och med 7.1970
Type 181 till och med 7.1971 Produktnummer : 1520 Original VW nummer : 111141165A, 111141167C
Urtrampningslager
Bubbla 1300, 1500 till och med 7.1970
Bubbla 1200 till och med 1972 (VIN 112 2670 582)
Karmann Ghia till och med 7.1970
Bus till och med 7.1970
Type 3 till och med 7.1970
Type 181 till och med 7.1971 Produktnummer : 1520 Original VW nummer : 111141165A, 111141167C
Urtrampningslager
Bubbla 1300, 1500 till och med 7.1970
Bubbla 1200 till och med 1972 (VIN 112 2670 582)
Karmann Ghia till och med 7.1970
Bus till och med 7.1970
Type 3 till och med 7.1970
Type 181 till och med 7.1971 Produktnummer : 1520 Original VW nummer : 111141165A, 111141167C
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 11 the clutch To disassemble the flywheel, you will need to loosen the gland nut, we discuss that in video 12. But first you will need to disassemble the clutch. You can do that when the engine is on the workbench, or hanging from an engine mount. In this video we show various techniques and tools to disassemble the clutch of your Type 1 Volkswagen engine without damage.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine overhaul - video 16 part 2 valves removal In Part 1, we showed the basic techniques for disassembling the valves and valve springs. We did this on a fairly new cylinder head.
When you`re dealing with a used cylinder head, disassembly may be a little less smooth.
Engine overhaul - video 13 replacing the crank seal During a complete engine overhaul, you will need to replace the crank seal. But replacement may also be necessary, when you discover an oil leak behind the flywheel, which will impair the operation of the clutch. We show in this video how to disassemble and reassemble the crank seal.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine overhaul - video 03 the workshop We show in this video what the possibilities are to work on your VW engine. If you plan to overhaul several engines, then buying a professional engine stand is recommended. If you only want to overhaul the engine of your own classic Volkswagen, then buying special tools is not cost effective. We will show all options.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine diagnostics - video 02 rockers and rocker arm In video fourteen of our engine overhaul video series, we disassembled and reassembled the rocker arms and rocker shaft. We will diagnose the rocker arms and rocker shaft in this video. Additional attention will be paid to the adjusting screws and adjusting nuts.
Engine diagnostics - video 04 part 1 valves and valve springs In video 16 of the engine overhaul series, we disassembled the valves and valve springs.
Not all of the cylinder heads we showed were in good condition, this does not mean that all parts need to be replaced. After a thorough diagnosis, it will show if the valves and valve springs are still reusable. This video discusses valve and valve spring diagnosis. It consists of four parts.