Varorna som visas här är relaterade till varandra med varan du valt och beställs eller söks ofta tillsammans.
Tips: får du ingen bra träff på sökordet du angivit så försök då att söka en vara som är relaterad till den. Finns det då en flik relaterade varor så kanske du hittar varan du sökte där.
Standard svänghjulsbult inkl. lager
Type 1 engine 30hp Produktnummer : 2091 Original VW nummer : 111105305C
Svänghjulbult standard med lager
Type 1 engines except 25hp+30hp and cars with automatic transmission
Type 3 engines except cars with automatic transmission
CT/CZ engines Produktnummer : 1535 Original VW nummer : 111105305E
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine overhaul - video 03 the workshop We show in this video what the possibilities are to work on your VW engine. If you plan to overhaul several engines, then buying a professional engine stand is recommended. If you only want to overhaul the engine of your own classic Volkswagen, then buying special tools is not cost effective. We will show all options.
crankshaft pulley removal Removing the crankshaft pulley on an engine that has run 100,000 km and more is best not done with just a hammer and brute force. You would prefer to reuse the original crankshaft pulley on your engine, were it not for the budget, also for the factory originality.
Engine overhaul - video 13 replacing the crank seal During a complete engine overhaul, you will need to replace the crank seal. But replacement may also be necessary, when you discover an oil leak behind the flywheel, which will impair the operation of the clutch. We show in this video how to disassemble and reassemble the crank seal.
Engine overhaul - video 16 part 2 valves removal In Part 1, we showed the basic techniques for disassembling the valves and valve springs. We did this on a fairly new cylinder head.
When you`re dealing with a used cylinder head, disassembly may be a little less smooth.