Oppmerksomhet: Alle norske bestillinger vil bli sendt av Winston VW Veteran AS (Sandnes, Norge),
så fraktkostnader er nå mye lavere og alle lokale avgifter er nå inkludert i prisen. På store karosserideler må det beregnes leveringstid, og høyere Innenlandsfrakt.
Delene som er nevnt her, har en nær sammenheng med den valgte delen og blir ofte bestilt sammen med den valgte delen eller søkt etter.
Tips: Hvis du ikke får et godt søkeresultat når du skriver inn et søkeord, prøv en del som har noe med det å gjøre, hvis det er en relatert fane, er den søkte delen ofte nevnt der.
Skum luffilter element
Height: 50 mm
Diameter: 135 mm
Fits air cleaner: #2148, #2152 and #5121 Artikkelnummer : 2147
Hvis den valgte delen ikke gjelder for din Volkswagen-type, kan du sjekke denne listen over de samme delene som passer på andre byggeår eller andre biltyper.
Air filter
Type 1 Motorer 1200cc 8.1975 og senere, 1300/1600cc 8.1971 og senere Artikkelnummer : 2149 Original VW nummer : 113129620
Air filter
Type 1 8.1974 og senere
Type 4 8.1972 og senere
CT/CZ
Waterboxer Motorer til 7.1985 (1900cc DF all years) Artikkelnummer : 42149 Original VW nummer : 021129620
Air filter
Type 1 8.1974 og senere
Type 4 8.1972 og senere
CT/CZ
Waterboxer Motorer til 7.1985 (1900cc DF all years) Artikkelnummer : 42149 Original VW nummer : 021129620
Air filter
Type 1 8.1974 og senere
Type 4 8.1972 og senere
CT/CZ
Waterboxer Motorer til 7.1985 (1900cc DF all years) Artikkelnummer : 42149 Original VW nummer : 021129620
Useful information from Paruzzi magazine and from our YouTube channel :
mixture preheating The engine is stopped as a result of poor combustion. This bad combustion is often caused by a, at that moment, wrong composition of the fuel in the cylinders. Because of this bad combustion, the engine does not deliver the desired power and you can feel this in the form of stuttering of the engine.
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
air filter thermostat The preheating of the fresh air supplied via the air filter to the carburettor is a part of our VW engine that gets too little attention. This system will ensure that in all weather conditions the carburettor is supplied with air at the right temperature. With these younger air filter models you don't have to adjust anything in contrast to the older models.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
Engine diagnostics - video 04 part 2 valves and valve springs In the second and third parts of this video, we will measure valve spring pressure. We begin in part 2 by measuring the valve spring pressure at open valve. Also known as the valve spring pressure at maximum valve lift. In part 3, we will measure the valve spring pressure at installed length.
Engine overhaul - video 16 part 2 valves removal In Part 1, we showed the basic techniques for disassembling the valves and valve springs. We did this on a fairly new cylinder head.
When you`re dealing with a used cylinder head, disassembly may be a little less smooth.
Engine overhaul - video 15 disassemble cylinder heads In this video, we will show how to disassemble the cylinder heads of a VW Type 1 engine, and what challenges you may face.
Engine adjustment - video 02 adjusting the rocker arms In the first video of this series, we adjusted the valve clearance. In addition to the valve clearance, the position of the rocker arm relative to the valve stem, is also a very important setting. If a rocker arm is not positioned correctly, it can be adjusted, which is called shimming.
air filter preheating It seems to be a natural part of your air-cooled engine, but the air filter plays a crucial role, it's like breathing in a human being. The carburettor is tasked with mixing petrol with air to deliver a flammable mixture. Petrol alone is not a good fuel. That requires oxygen and not just a little bit of it.