Specifications:
Bolt:
Thread size: M20 x 1.5
Length: 20 mm
Washer:
Inner size: 20.7 mm
Outer size: 44 mm
Thickness: 2 mm
Fel:
-The crankshaft bolt has superficial rust
Vad är en Second Chance reservdel? En reservdel är en del som har returnerats av en kund och som inte längre kan säljas som ny eller som har skadats under transporten. Skador eller ofullständighet är de vanligaste defekterna. Felet beskrivs ovan och bilden är den verkliga representationen av den relevanta delen. Klicka på det ursprungliga Paruzzi-numret för mer information om delen och bilder på originaldelen.
Andrahandsdelar kan inte returneras och har inte någon form av garanti, men du får en trevlig rabatt på nypriset.
Useful information from Paruzzi magazine and from our YouTube channel :
crankshaft end play Whether an oil leak is caused by a defective crankshaft seal or O-ring/packaging is not always easy to determine. At the bottom of the engine, near the flywheel, where the gearbox and the engine are connected to each other, you will see traces of engine oil.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
finding the top dead center What does Top Dead Center (TDC) actually mean? If you study the theory of the operation of an internal combustion engine - or the "petrol engine" - it will become clear. Without going into too much detail about the theory, we have to talk about the otto cycle, better known as the four stroke cycle.
Engine diagnostics - video 03 pushrods In video fourteen of our series on engine overhaul, we disassembled and reassembled the rocker arms and pushrods. In this video, we will inspect the pushrods. The result of this diagnosis, will tell us if we can reinsert the pushrods, or if we need to replace them.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine overhaul - video 12 the flywheel In this video, we'll explain how to disassemble and assemble the flywheel, and what tools you'll need to do so. To disassemble the flywheel, you will need to unscrew the gland nut. This nut is attached with a torque of 350 Nm, it will require some force to loosen.
Engine overhaul - video 16 part 1 valves removal In this first part of video 16, we disassemble cylinder head valves and valve springs. In the first part, we start by demonstrating the tools and techniques used, and disassemble the valves of a relatively new cylinder head.
measure crankshaft end play The play is caused by wear of the engine, this is actually very normal, and will occur faster with performance engines. With normal use of standard VW engines in combination with a good maintenance of the engine, wear will not occur quickly.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
Engine Overhaul - video 02 overhauled engines We show in this video all the engines that we overhauled for the video series. An AB 1300, an AS 1600, an AJ 1600 and a D 1200 engine, every step, every detail of the overhaul of these air-cooled Volkswagen engines will be discussed in this series.