Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Moottorin uudelleenkorjaus 1641cc W-110 (uusi kotelo) ja ytimen talletus
Type 1 moottori 1641cc joissa W-110 camshaft
Note:
Price includes €370,-core deposit. Tuotenumero : 5545
Moottorin 1600cc (AD / AJ / AS) uudelleenkorjaus (uusi kotelo) ja ytimen talletus
Type 1 moottori 1600cc (moottoritcode AD, AJ or AS) dual port joissa 200 mm flywheel
Note:
Price includes €370,-core deposit. Tuotenumero : 5503 Alkuperäinen VW-numero : 211100033
€ 4670,00
Moottori rakennetaan asiakastilauksesta, jolloin toimitusaika on vähintään 12 viikkoa.
Moottorin uudelleenkorjaus 1600cc (AS) (uusi kotelo) ja ytimen talletus
Type 1 moottori Bussi 1600cc (moottoritcode AS) dual port joissa 215 mm flywheel
Note:
Price includes €370,-core deposit. Tuotenumero : 25522
Useful information from Paruzzi magazine and from our YouTube channel :
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
Engine overhaul - video 16 part 1 valves removal In this first part of video 16, we disassemble cylinder head valves and valve springs. In the first part, we start by demonstrating the tools and techniques used, and disassemble the valves of a relatively new cylinder head.
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
Engine overhaul - video 03 the workshop We show in this video what the possibilities are to work on your VW engine. If you plan to overhaul several engines, then buying a professional engine stand is recommended. If you only want to overhaul the engine of your own classic Volkswagen, then buying special tools is not cost effective. We will show all options.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
crankshaft end play Whether an oil leak is caused by a defective crankshaft seal or O-ring/packaging is not always easy to determine. At the bottom of the engine, near the flywheel, where the gearbox and the engine are connected to each other, you will see traces of engine oil.