Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Vaahto ilmansuodattimen patruuna
Height: 50 mm
Halkaisija: 135 mm
Fits air cleaner: #2148, #2152 ja #5121 Tuotenumero : 2147
Jos valittu osa ei sovi valitsemaasi VW-tyyppiin, tarkastele tältä listalta vastaavia osia jotka sopivat muihin vuosimalleihin tai muihin VW-tyyppeihin.
Ilmansuodatin, vakio
Type 1 8.1974 ja uudemmat
Type 4 8.1972 ja uudemmat
CT / CZ
Waterboxer moottori-7.1985 (1900cc DF kaikki vuosimallit) Tuotenumero : 42149 Alkuperäinen VW-numero : 021129620
Ilmansuodatin, vakio
Type 1 8.1974 ja uudemmat
Type 4 8.1972 ja uudemmat
CT / CZ
Waterboxer moottori-7.1985 (1900cc DF kaikki vuosimallit) Tuotenumero : 42149 Alkuperäinen VW-numero : 021129620
Ilmansuodatin, vakio
Type 1 8.1974 ja uudemmat
Type 4 8.1972 ja uudemmat
CT / CZ
Waterboxer moottori-7.1985 (1900cc DF kaikki vuosimallit) Tuotenumero : 42149 Alkuperäinen VW-numero : 021129620
Useful information from Paruzzi magazine and from our YouTube channel :
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
Engine Overhaul - video 01 video series preview In this video, we will give an overview of the most important steps during the engine overhaul of a type 1 air-cooled Volkswagen engine. Each step will be discussed in a separate video. We will show special tools and even homemade tools to help the enthusiast perform their engine overhaul.
Engine overhaul - video 11 the clutch To disassemble the flywheel, you will need to loosen the gland nut, we discuss that in video 12. But first you will need to disassemble the clutch. You can do that when the engine is on the workbench, or hanging from an engine mount. In this video we show various techniques and tools to disassemble the clutch of your Type 1 Volkswagen engine without damage.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
Engine overhaul - video 16 part 1 valves removal In this first part of video 16, we disassemble cylinder head valves and valve springs. In the first part, we start by demonstrating the tools and techniques used, and disassemble the valves of a relatively new cylinder head.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
Engine overhaul - video 13 replacing the crank seal During a complete engine overhaul, you will need to replace the crank seal. But replacement may also be necessary, when you discover an oil leak behind the flywheel, which will impair the operation of the clutch. We show in this video how to disassemble and reassemble the crank seal.
Engine overhaul - video 16 part 2 valves removal In Part 1, we showed the basic techniques for disassembling the valves and valve springs. We did this on a fairly new cylinder head.
When you`re dealing with a used cylinder head, disassembly may be a little less smooth.