Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Kytkinlevy 180 mm
Type 1 moottori 25hp + 30hp
Type 1 moottori 1300
Type 1 moottori 1200-1980 (D 1455271)
Type 3 moottori-7.1962 Tuotenumero : 1500 Alkuperäinen VW-numero : 111141031F, 111141031DX, 111141031GX
Kytkimen paineasetelma 180 mm
Type 1 moottori 25hp + 30hp
Type 1 moottori 1300-7.1970
Type 1 moottori 1200-1972 (VIN 112 2670 582)
Type 3 moottori-7.1962 Tuotenumero : 1509 Alkuperäinen VW-numero : 111141025DX
Paineasetelma 200 mm
Type 1 moottori 1200 (D 1 455 271) ja uudemmat
Type 1 moottori 1600 (TYP-1 Kupla, Karmann Ghia, 181)
Type 1 moottori 1600 (Bussi-1975 VIN 216 2118 505)
Type 3 moottori 8.1970 ja uudemmat Tuotenumero : 1507 Alkuperäinen VW-numero : 311141025CX, BAA141025, 043141025B
Jos valittu osa ei sovi valitsemaasi VW-tyyppiin, tarkastele tältä listalta vastaavia osia jotka sopivat muihin vuosimalleihin tai muihin VW-tyyppeihin.
Painelaakeri
TYP-1 Kupla 1300, 1302, 1303 8.1970 ja uudemmat
TYP-1 Kupla 1200 1972 (VIN 112 2670 583) ja uudemmat
Karmann Ghia 8.1970 ja uudemmat
Bussi 8.1970 ja uudemmat
TYP-3 8.1970 ja uudemmat
TYP 181 8.1971 ja uudemmat Tuotenumero : 1521 Alkuperäinen VW-numero : 113141165B, 091141165D, 088141165A
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
crankshaft seal replacement If you find that the crankshaft clearance is outside the factory specifications, replacing the crankshaft seal will not be a solution for the oil leak you have identified. If the crankshaft clearance is less than 0.30 mm, it makes sense to replace the oil seal, otherwise a total engine overhaul is the only worthwhile option.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
Engine Overhaul - video 01 video series preview In this video, we will give an overview of the most important steps during the engine overhaul of a type 1 air-cooled Volkswagen engine. Each step will be discussed in a separate video. We will show special tools and even homemade tools to help the enthusiast perform their engine overhaul.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?
Engine overhaul - video 11 the clutch To disassemble the flywheel, you will need to loosen the gland nut, we discuss that in video 12. But first you will need to disassemble the clutch. You can do that when the engine is on the workbench, or hanging from an engine mount. In this video we show various techniques and tools to disassemble the clutch of your Type 1 Volkswagen engine without damage.
Engine overhaul - video 12 the flywheel In this video, we'll explain how to disassemble and assemble the flywheel, and what tools you'll need to do so. To disassemble the flywheel, you will need to unscrew the gland nut. This nut is attached with a torque of 350 Nm, it will require some force to loosen.
Engine overhaul - video 03 the workshop We show in this video what the possibilities are to work on your VW engine. If you plan to overhaul several engines, then buying a professional engine stand is recommended. If you only want to overhaul the engine of your own classic Volkswagen, then buying special tools is not cost effective. We will show all options.