Sopii malleihin: Type 1 moottori 1200cc 1980 (D 1 455 272) ja uudemmat
Type 1 moottori 1500cc
Type 1 moottori 1600cc (Bussi-1975 VIN 216 2118 505)
Type 3 moottori 8.1962 ja uudemmat
Näitä tuotteita tilataan usein samalla kuin valitsemaasi tuotetta. Vihje: jos et löydä etsimääsi tuotetta, hae hakusanalla joka joka liittyy jollain tavalla osakokonaisuuteen, ja tarkastele tässä esiteltäviä liitännäisiä tuotteita.
Puhdistusspray
Content: 500 ml Tuotenumero : 50150
Useful information from Paruzzi magazine and from our YouTube channel :
the clutch: basic concept For a long time I wondered how the clutch in our Volkswagen Fastback worked, I was only six years old. I didn't understand very well that by releasing a pedal our VW started to drive spontaneously. Well, if you understand how disc brakes work, then the step to understanding how the clutch mechanism works is not far.
Engine diagnostics - video 03 pushrods In video fourteen of our series on engine overhaul, we disassembled and reassembled the rocker arms and pushrods. In this video, we will inspect the pushrods. The result of this diagnosis, will tell us if we can reinsert the pushrods, or if we need to replace them.
Engine Overhaul - video 01 video series preview In this video, we will give an overview of the most important steps during the engine overhaul of a type 1 air-cooled Volkswagen engine. Each step will be discussed in a separate video. We will show special tools and even homemade tools to help the enthusiast perform their engine overhaul.
oil leakage If you are planning to buy a classic Volkswagen, you will certainly take a look under the engine lid and under the car. If it's dirty both at the bottom and under the bonnet, it doesn't offer much trust. The engine will need a lot of attention in the coming weeks, but how bad is it?
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine overhaul - video 07 TDC compression in practice In video six, we explained the operation of the four-stroke internal combustion engine through animations. In this video we will look at how to determine the top dead centre of cylinder 1 in practice. We will also learn how to find the compression stroke of cylinder 1, different techniques will be shown.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.