As peças aqui mencionadas têm uma relação forte com a peça seleccionada e são frequentemente encomendadas juntamente com a peça seleccionada ou procuradas. Tip: Se não receber um bom resultado de busca quando entrar numa palavra-chave, tenta uma parte que tenha algo a ver com ela, se existe uma lista relatada, o item revistado é frequentemente mencionado lá
Reconstrução do motor 1775cc (caixa nova) e depósito do núcleo
Type 1 motores 1775cc
Nota:
Price includes €370,- core deposit. Referência Paruzzi : 5546
Reconstrução do motor 1600cc (AD/AJ/AS) (caixa nova) e depósito do núcleo
Type 1 motores 1600cc (motorescode AD, AJ or AS) dual port with 200 mm flywheel
Nota:
Price includes €370,- core deposit. Referência Paruzzi : 5503 Referencia VW original : 211100033
€ 3752,07 excluindo IVA € 4540.00 incluindo IVA
O motor será especialmente construído para si, o que significa que o tempo de entrega é de pelo menos 10 semanas.
Useful information from Paruzzi magazine and from our YouTube channel :
Engine diagnostics - video 02 rockers and rocker arm In video fourteen of our engine overhaul video series, we disassembled and reassembled the rocker arms and rocker shaft. We will diagnose the rocker arms and rocker shaft in this video. Additional attention will be paid to the adjusting screws and adjusting nuts.
Engine diagnostics - video 03 pushrods In video fourteen of our series on engine overhaul, we disassembled and reassembled the rocker arms and pushrods. In this video, we will inspect the pushrods. The result of this diagnosis, will tell us if we can reinsert the pushrods, or if we need to replace them.
Engine adjustment - video 01 valve clearance The valve clearance is the first thing to check when adjusting an engine. If the valve clearance is not adjusted properly, then adjusting for example, the ignition, or the carburetor, will do little good. In this video we will show you how to adjust the valve clearance.
Engine overhaul - video 16 part 2 valves removal In Part 1, we showed the basic techniques for disassembling the valves and valve springs. We did this on a fairly new cylinder head.
When you`re dealing with a used cylinder head, disassembly may be a little less smooth.
removing the engine The air-cooled Volkswagen is an ingenious design, but not all work can be done with built-in engine, unfortunately. Sometimes it is also much more comfortable to work with the engine on the workbench hanging from an engine mount.
crankshaft end play Whether an oil leak is caused by a defective crankshaft seal or O-ring/packaging is not always easy to determine. At the bottom of the engine, near the flywheel, where the gearbox and the engine are connected to each other, you will see traces of engine oil.
Engine overhaul - video 06 find the TDC compression stroke We will explain in this video how to determine the top dead center, as well as which of the two top dead center moments is this one from the compression stroke. This is important in order to properly position the distributor drive shaft. Properly understanding how a four-stroke engine works is essential when you begin an engine overhaul.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
installing the engine In edition 16 we explained how to remove the engine of a VW Beetle, two techniques were discussed. The most important points of attention for the installation of the engine are indicated in this article. During the installation of the engine you will have to position the pilot shaft of the gearbox perfectly opposite the centre of the clutch.